MAG-INSTALL GABAY
CSEN1

CSEN1 Combo Sensor Controller

Part Numbers: CSEN1-H-W-ZHA (white enclosure) and CSEN1-H-G-ZHA (gray enclosure)

PAGLALARAWAN

The CSEN1 is a low voltage Networked Lighting Controller with an integrated passive infrared sensor and a photocell. It is powered via the AUX power from the LED driver. The CSEN1 autodetects both 0-10V Drivers and D4i Drivers to simplify the installation. The product is DLC certified for both indoor and outdoor applications.

MGA ESPISIPIKASYON

• Dalas ng Radyo: 2.4 GHz (IEEE 802.15.4)
• RF Transmission Output Power: +20dBM
• Temperatura sa Pagpapatakbo: -40° hanggang +70° C
• Operating Humidity: 10 hanggang 95%, non-condensing
• IP66 Rated Enclosure
• Mga Dimensyon: 3.1" D x 1.6" H (80mm D x 42mm H)
• Input Power: 12-24VDC, 35mA max, 840mW
• Layunin ng kontrol: Pagpapatakbo
• Environmental: Indoor/Outdoor
• Degree ng Polusyon: 3
• Na-rate na Impulse Voltage: 330V

CONSIDERASYON SA DISENYO

Below are some recommendations for successful analog dimming using the CSEN1. The analog dimming control wires are referenced as DALI+/DIM+ and Common Ground/DALI-. The dimming signals have a Maximum voltage ng 10V DC.

• Do not ground the Common Ground/DALI- wire to chassis ground; this is a return signal and is critical for proper dimming.
• I-ruta ang pagdidilim ng mga wire palayo sa mga linya ng AC kung maaari.
• Pinakamataas na 4 DALI-2/D4i LED Driver bawat controller, kumunsulta sa Synapse Support kung kailangan ng mas malaking ratio.
• Maximum of 8 DIM to OFF LED Drivers for DIM to OFF Designs.
• Huwag i-mount sa isang heatsink o sa isang LED driver.

TANDAAN: Dapat suportahan ng LED Driver ang DIM to OFF functionality.
MGA BABALA AT MAG-INGAT

• TURN OFF POWER AT CIRCUIT BREAKER OR FUSE AND TEST THAT POWER IS OFF BEFORE INSTALLING OR SERVICING!
• The CSEN1 should only be installed in a fixture with a Zhaga Book 18 receptacle.
• Ang pagkabigong sundin ang mga tagubilin at babala na ito ay maaaring potensyal na mapawalang-bisa ang warranty.
• This product must be installed in accordance with national, state, and local electrical codes and requirements.
• If you are unsure about any part of these instructions, consult an electrician; qualified personnel should perform all work.

MGA DETALYE NG WIRING NG ZHAGA BOOK 18 SOCKET

TURN OFF POWER AT CIRCUIT BREAKER OR FUSE AND TEST THAT POWER IS OFF BEFORE INSTALLING OR SERVICING!
For fixtures with an existing Zhaga socket, prior to installation, verify the wiring per the details below. (See Figure 1) If the fixture does not have a Zhaga socket, use the appropriate Wired Adapter accessory based on the knockout size: CSEN1-ZHA-ADPT-22 for 22mm knockouts, or CSEN1-ZHA-ADPT-33 for 33mm knockouts. The specifications for the signal wires are:

• 12-24VDC POWER: Brown
• Common Ground/DALI-: Pink with White Stripe
• DALI+/DIM+: Violet with White Stripe
• Solid Conductor, 105°C, Rated for 600VAC, AWG 20, 15” Length

FIGURE 1

MGA INSTRUKSYON SA PAG-INSTALL

TURN OFF POWER AT CIRCUIT BREAKER OR FUSE AND TEST THAT POWER IS OFF BEFORE INSTALLING OR SERVICING!

1. Kung naaangkop, tanggalin ang sealing cap o lighting control device na kasalukuyang naka-install sa fixture receptacle.
2. Align the CSEN1 such that the contacts pins are positioned at the appropriate the receptacle contacts.
3. After alignment, push until the CSEN1 is fully seated within the receptacle.
4. While pushing against the device, twist the CSEN1 housing clockwise until it locks into place. The CSEN1 includes a latching key or notch that will lock into position with an audible “click”. (See Figure 2)

Tandaan: Upang gumana nang maayos, tiyaking ganap na naipasok ang controller sa socket at naka-twist sa naka-lock na posisyon.
Babala: The Zhaga receptacle should not turn during installation. Turning the receptacle could damage the internal fixture wiring by pulling it loose.
FIGURE 2

Mga LED na STATUS

Power LED	Katayuan
Asul	On for 3 seconds at Startup, then Off
Katayuan ng LED	Katayuan
Pula	No script on the device
Kumikislap na Pula	Error sa Komunikasyon
Kumikislap na Blue	Communication, No Config
Kumikislap na Berde	Normal Operation with Motion
Naka-off	Normal Operation, no Motion

IMPORMASYON AT MGA SERTIPIKASYON SA REGULATORY
RF Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance of 20cm between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
Mga certification ng Industry Canada (IC): Ang digital apparatus na ito ay hindi lalampas sa Class B na mga limitasyon para sa radio noise emissions mula sa digital apparatus na itinakda sa Radio Interference Regulations ng Canadian Department of Communications.
Mga sertipikasyon ng FCC at impormasyon sa regulasyon (USA lang)
FCC Part 15 Class B: Ang device na ito ay sumusunod sa part 15 ng FCC rules. Ang operasyon ay napapailalim sa sumusunod na dalawang kundisyon: (1) Ang mga device na ito ay maaaring hindi magdulot ng mapaminsalang interference, at (2) Dapat tanggapin ng mga device na ito ang anumang interference na natanggap, kabilang ang interference na maaaring magdulot ng mapaminsalang operasyon.
RADIO FREQUENCY INTERFERENCE (RFI) (FCC 15.105): This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: (1) Re-orient or relocate the receiving antenna; (2) Increase the separation between the equipment and the receiver; (3) Connect the equipment into an outlet on a circuit different from that to which the receiver is connected; (4) Consult the dealer or an experienced radio/TV technician for help.
Declaration of Conformity (FCC 96-208 & 95-19): Synapse Wireless, Inc. declares that the product name CSEN1 to which this declaration relates, meet the requirements specified by the Federal Communications Commission as detailed in the following specifications:

• Bahagi 15, Subpart B, para sa kagamitan ng Class B
• FCC 96-208 dahil nalalapat ito sa mga personal na computer at peripheral ng Class B
• Ang produktong ito ay nasubok sa isang External Test Laboratory na na-certify ayon sa mga panuntunan ng FCC at napag-alamang nakakatugon sa FCC, Part 15, Mga Limitasyon sa Emisyon. Naka-on ang dokumentasyon file at makukuha mula sa Synapse Wireless, Inc.

Kung ang FCC ID para sa module sa loob ng enclosure ng produktong ito ay hindi nakikita kapag naka-install sa loob ng isa pang device, ang labas ng device kung saan naka-install ang produktong ito ay dapat ding magpakita ng label na tumutukoy sa nakalakip na module na FCC ID. Mga Pagbabago (FCC 15.21):
Ang mga pagbabago o pagbabago sa kagamitang ito na hindi hayagang inaprubahan ng Synapse Wireless, Inc., ay maaaring magpawalang-bisa sa awtoridad ng gumagamit na patakbuhin ang kagamitang ito.
Patented – virtual na pagmamarka sa https://www.synapsewireless.com/about/patents
Upang matuto nang higit pa bisitahin ang: synapsewireless.com

MGA SERTIPIKASYON

Modelo	CSEN1-H-W-ZHA (white enclosure) or CSEN1-H-G-ZHA (gray enclosure)
Naglalaman ng FCC ID	QOQ-GM240P
Naglalaman ng IC	5123A-GM240P
RoHS 3	2011/65/EU (2015/863)
EU REACH	(EC) No 1907/2006

DALI-2 Certified Application Controller

 

Mga Dokumento / Mga Mapagkukunan

Synapse CSEN1 Combo Sensor Controller [pdf] Gabay sa Pag-install CSEN1-H-W-ZHA, CSEN1-H-G-ZHA, CSEN1 Combo Sensor Controller, CSEN1, Combo Sensor Controller, Sensor Controller, Controller

Mga sanggunian

• User Manual