LTECH KMS1 Switch Module
Panimula ng Produkto
- Fully supports major smart home ecosystems including Apple Home, SmartThings, Google Assistant, and Amazon, enabling unified management across platforms.
- Built-in Thread module, compatible with the Matter protocol, supports Siri, Google, and Alexa voice control.
- Supports OTA firmware updates to continuously receive the latest features and security patches, ensuring long-term device stability.
- Parameter settings for switch type and power-on status can be completed via the NFC Lighting App.
- Reserved mechanical switch/reset switch interface accommodates both traditional operating habits and smart scenario requirements.
Teknikal na Pagtutukoy
| Modelo | KMS1 |
|---|---|
| Uri ng wireless | Bagay sa Thread |
| Lumipat ng channel | 1CH |
| Operating voltage | 100-240V~, 50/60Hz |
| Mga parameter ng maximum load ng relay | Resistive load: 1000W@230Vac, 500W@110Vac Capacitive load: 400W@230Vac, 200W@110Vac |
| Relay surge kasalukuyang | 70A@10ms |
| Temperatura ng pagtatrabaho | -25°C~50°C |
| Laki ng produkto | L45×W45.5×H20.5(mm) |
| Timbang ng produkto | 38g |
| Mga pamantayan | UL 8750, EN 61347-2-13:2014+A1:2017, EN 61347-1:2015+A1:2021, EN 62493:2015/A1:2022 |
Mga Larawan ng Produkto
DIMENSYON
- Yunit: mm
- Mga Dimensyon: 45 x 45.5 x 20.5
Wiring Diagram
- Diagram ng Kable ng Mekanikal na Switch
Includes connections for load, line (L), and neutral (N).
- Diagram ng mga kable ng Push Switch
Includes connections for load, line (L), and neutral (N).
Gamitin ang NFC Lighting APP
Scan the QR code with your mobile phone and install the APP as prompted. Compatible with iOS 13 or above and Android NFC-enabled models.
Read the Device
Click “Read/Write LED driver” in the APP [home page], place the sensing area of the phone near the NFC identification point of the driver, and read the device parameters.
I-edit ang Mga Parameter
Click “Parameter Management” to select the switch type. When selecting a reset switch, you can configure the device’s power-on state function.
Add to Matter Platform Instructions
- This device supports control via major smart home platforms, including Apple Home, Amazon Alexa, Google Home, Smart Things, and others.
- To connect Matter over Thread devices, prepare a Matter hub supporting Thread border router functionality from major platforms.
Mga Katugmang Modelo
Pag-setup Halample
- This guide uses Apple Home as an example. Prepare an iPhone (iOS 16.2 or later) or iPad (iPadOS 16.2 or later) with the latest firmware, along with an Apple HomePod mini also running the latest firmware. Connect your iPhone or iPad to your home Wi-Fi network, launch the Apple Home app, and follow Apple’s instructions to set up the HomePod mini.
- For iPhone models 15 and above, no Matter hub is required; they can be added directly.
Magdagdag ng Mga Accessory
- Open the Apple Home app and tap “Add or Scan Accessories.” Add the device to Apple Home by scanning the QR code sticker on the device.
- *You can also activate service via NFC: Simply hold your iPhone 16 or later model near the device’s NFC sensor area to be recognized and activated.
Kontrolin ang Device
After successfully adding the device to Apple Home, tap the device icon to turn it on or off.
Mga Advanced na Tampok
Supports creating groups, scenes, and automations, as well as remote control and scheduled control. Devices can also be controlled via Siri voice commands.
Ibalik ang Mga Setting ng Pabrika
Reset Button Reset
Press and hold the reset button for 15 seconds until the indicator light flashes red rapidly, then release. Within 3 seconds, press the reset button three times briefly. The red light will then switch to slow flashing, indicating the device has begun restoring factory settings. When the indicator light flashes blue rapidly, the restoration is complete.
Pag-reset ng Power-on
Kung sakaling magkaroon ng kapangyarihan outage, use the switch to power on the device for 15 seconds before powering it off. Repeat this power cycle six times consecutively (each cycle consisting of 2 seconds on and 5 seconds off). After the seventh power cycle, the load lamp will flash three times, indicating a successful reset to factory settings.
Pansin
- Ang pag-install at pag-commissioning ng produkto ay dapat gawin ng isang kwalipikadong propesyonal.
- Our company products are not waterproof or lightning-proof (special models excepted). Please avoid the sun and rain. When installed outdoors, please ensure they are mounted in a waterproof enclosure or in an area equipped with lightning protection devices.
- Ang mahusay na pag-aalis ng init ay magpapahaba sa buhay ng trabaho ng mga produkto. Pakitiyak na maayos ang bentilasyon.
- Mangyaring suriin kung gumagana ang voltage ang ginamit ay sumusunod sa mga kinakailangan sa parameter ng mga produkto.
- Ang diameter ng wire na ginamit ay dapat na mai-load ang mga light fixture na iyong ikinonekta at matiyak ang matatag na mga kable.
- Bago mo i-on ang mga produkto, pakitiyak na tama ang lahat ng mga wiring kung sakaling magkaroon ng maling koneksyon na magdulot ng pinsala sa mga light fixture.
- Kung may naganap na pagkakamali, mangyaring huwag subukang ayusin ang mga produkto nang mag-isa. Kung mayroon kang anumang tanong, mangyaring makipag-ugnayan sa iyong mga supplier.
Kasunduan sa Warranty
Mga panahon ng warranty mula sa petsa ng paghahatid: 2 taon. Ang mga libreng serbisyo sa pagkukumpuni o pagpapalit para sa mga problema sa kalidad ay ibinibigay sa loob ng mga panahon ng warranty.
Mga Pagbubukod sa Warranty
- Lampas sa panahon ng warranty.
- Anumang artipisyal na pinsala na dulot ng mataas na voltage, labis na karga, o hindi wastong mga operasyon.
- Mga produktong may matinding pisikal na pinsala.
- Pinsala na dulot ng mga natural na kalamidad at force majeure.
- Nasira ang mga label ng warranty at barcode.
- No contract signed by our company.
Mga Dokumento / Mga Mapagkukunan
 |
LTECH KMS1 Switch Module [pdf] Manwal ng May-ari KMS1 Switch Module, KMS1, Switch Module, Module |